network Integration
cisco-wireless-access-point (en)


ServicePilot network-cisco-wireless-access-point


# Cisco Wireless Access Point

Overview

This package is designed to monitor a Cisco Wifi Access Point in terms of resources and statistics using SNMP.

Description

ServicePilot uses SNMP to monitor Cisco Wifi Access Point in terms of:

  • system statistics (CPU, memory and Buffer creation failure),
  • Network and Wireless interface statistics.

Requirements

  • SNMP service must be installed, configured and started on the targeted Cisco Wifi Access Point device (Security: read-only SNMP community and allowed host must be set).

  • Network Flows - It is is necessary to ensure network connectivity between ServicePilot and the monitored device. In case of a network infrastructure using a firewall, all the ports below must be opened:

    • UDP/161 (SNMP): Between ServicePilot Manager and Cisco Wifi Access Point
    • ICMP/Echo Request (Ping): Between ServicePilot Manager and Cisco Wifi Access Point
    • UDP/162 (SNMP Trap): (Optional) Between Cisco Wifi Access Point and ServicePilot Agent
  • ServicePilot Requirements

    • ServicePilot Manager minimum version: 8.5

Installation

Before adding a resource to monitor, make certain that all pre-requisites are in place and if a ServicePilot Agent is required, that it is communicating correctly with the ServicePilot Manager. Resources can be added to ServicePilot configuration in a number of ways:

Add resource using Views Configuration web interface

  1. As an administrative user of ServicePilot, open the ServicePilot web interface.
  2. Navigate to Administration. The Configuration > Views web page will open.
  3. Click on the view in which to place the new resource in the Views hierarchy on the left of the interface. The View editor section will show the existing view contents.
  4. From the Packages list on the right of the interface, click and drag the network-cisco-wireless-access-point package into the View editor and let go.
  5. The Package properties dialog box will open to allow resource configuration.
  6. Click OK to close the Package properties dialog box. Note that the dialog box will not close if required parameters are not set.
  7. Click Save to apply the new resource to ServicePilot configuration.

Add resource by changing servicepilot.conf configuration file

Resources can be added to ServicePilot configuration by directly editing the servicepilot.conf or other included YAML configuration files. The ServicePilot web interface can be used to make these changes and apply them to the running configuration.

  1. As an administrative user of ServicePilot, open the ServicePilot web interface.
  2. Navigate to Administration.
  3. Navigate to Configuration > Edit configuration.
  4. Expand the configuration to find the provisioning: and then packages: section of the view in which the new resource will be placed.
  5. Add the example package configuration line below.
  6. Click on the green - package: word to open then Package properties dialog box to allow resource configuration.
  7. Click OK to close the Package properties dialog box. Note that the dialog box will not close if required parameters are not set.
  8. Click Save to apply the new resource to ServicePilot configuration.

Example:

- package: "network-cisco-wireless-access-point;;;;;;;;network-cisco-wireless-access-point;;127.0.0.1;Y;N;;"

Key field notes

In the Monitoring Policies tab, specify the policy or policies to apply to the package

  1. Basic Parameters tab:

    1. IP address/FQDN: Specify the IP address, host name or FQDN for the Cisco Wireless Access Point, as resolvable by the machine on which ServicePilot Manager is running
  2. Interfaces tab:

    1. Auto Discover Interfaces: Set it on to get statistics for interfaces.
    2. Use Interface filter instead of Addressing Information: Set it on to get statistics for a specified list on interfaces only. Set it off to get statistics for all available interfaces
    3. {Optional} Ignored Interfaces names separated with '|': Specify name(s) of interface(s) NOT to be monitored
    4. {Optional} Allowed Interfaces names separated with '|': Specify name(s) of interface(s) to be monitored

Note: Each element of the ignored/allowed interface lists is a regular expression as defined by Like Operator (Visual Basic)

Notes

MIBs Used:

  • RFC1213-MIB2
  • CISCO-MEMORY-POOL-MIB
  • CISCO-PROCESS-MIB
  • CISCO-DOT11-ASSOCIATION-MIB
network cisco-wireless-access-point 0

network cisco-wireless-access-point 1

network cisco-wireless-access-point 2