network Integration
cisco-ucs (en)


ServicePilot network-cisco-ucs


# Cisco UCS

Overview

This package aims at monitoring Cisco UCS Architecture using SNMP.

Description

ServicePilot uses SNMP to monitor Cisco UCS Architecture in terms of:

  • Global System Information
  • Fabric Interconnect health and performance (Interfaces, Fans, Temperature sensors and Power Supplies)
  • Chassis health and performance (Interfaces, Fans, Temperature sensors,Power Supplies)
  • Blade Servers health and performance on each chassis

Requirements

  • SNMP Service must be configured (Security: read-only SNMP community and allowed host must be set) and started on each target device.

  • Network Flows - It is necessary to ensure network connectivity between ServicePilot and the monitored device. In case of a network infrastructure with a firewall, all of the following flows must be opened:

    • UDP/161 (SNMP): Between ServicePilot Manager and Cisco UCS
  • ServicePilot Requirements

    • ServicePilot Manager minimum version: 8.5

Installation

Before adding a resource to monitor, make certain that all pre-requisites are in place and if a ServicePilot Agent is required, that it is communicating correctly with the ServicePilot Manager. Resources can be added to ServicePilot configuration in a number of ways:

Add resource using Views Configuration web interface

  1. As an administrative user of ServicePilot, open the ServicePilot web interface.
  2. Navigate to Administration. The Configuration > Views web page will open.
  3. Click on the view in which to place the new resource in the Views hierarchy on the left of the interface. The View editor section will show the existing view contents.
  4. From the Packages list on the right of the interface, click and drag the network-cisco-ucs package into the View editor and let go.
  5. The Package properties dialog box will open to allow resource configuration.
  6. Click OK to close the Package properties dialog box. Note that the dialog box will not close if required parameters are not set.
  7. Click Save to apply the new resource to ServicePilot configuration.

Add resource by changing servicepilot.conf configuration file

Resources can be added to ServicePilot configuration by directly editing the servicepilot.conf or other included YAML configuration files. The ServicePilot web interface can be used to make these changes and apply them to the running configuration.

  1. As an administrative user of ServicePilot, open the ServicePilot web interface.
  2. Navigate to Administration.
  3. Navigate to Configuration > Edit configuration.
  4. Expand the configuration to find the provisioning: and then packages: section of the view in which the new resource will be placed.
  5. Add the example package configuration line below.
  6. Click on the green - package: word to open then Package properties dialog box to allow resource configuration.
  7. Click OK to close the Package properties dialog box. Note that the dialog box will not close if required parameters are not set.
  8. Click Save to apply the new resource to ServicePilot configuration.

Example:

- package: "network-cisco-ucs;;;;;;;;network-cisco-ucs;;127.0.0.1;;127.0.0.1;;127.0.0.1;;N;Y;Y;Y;Y;Y;Y"

Key field notes

In the Monitoring Policies tab, specify the policy or policies to apply to the package

  1. Basic Parameters tab:

    1. UCS Virtual IP address: Virtual IP address of the Cisco UCS Unit being added
  2. Monitoring Options tab: select the resources to monitor

  3. Fabric Interconnect tab:

    1. Fabric Interconnect A: Specify the name of the Fabric Interconnect A
    2. IP address A: Specify the IP address of Fabric Interconnect A, as resolvable by the machine on which ServicePilot Manager is running
    3. Fabric Interconnect B: Specify the name of the Fabric Interconnect B
    4. IP address B: Specify the IP address of Fabric Interconnect B, as resolvable by the machine on which ServicePilot Manager is running

Notes

MIBs Used:

  • RFC1213-MIB2
  • CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB
  • CISCO-UNIFIED-COMPUTING-COMPUTE-MIB
  • CISCO-SYSTEM-EXT-MIB
  • CISCO-ENTITY-SENSOR-MIB
network cisco-ucs 0

network cisco-ucs 1

network cisco-ucs 2

network cisco-ucs 3